 |
Manufacturers Exporters and Suppliers of Tractor Mounted Drilling Rigs - KLR TBW 40, DTH Drill Rig, Dth Drilling Rigs, Tractor Mounted Dth Drilling Rigs, Trolley Mounted Dth Drilling Rigs, Skid Mounted Dth Drilling Rigs, Dth Rotary Drilling Rigs, Trailer Mounted Dth Drilling Rigs, Mini Dth Drilling Rigs, Hydraulic Dth Drilling Rigs, Hand Pump Dth Drilling Rigs, Water Well Dth Drilling Rigs, Dth Combination Drilling Rigs. |
 |
   |
| |
HOME | CONTACT US | SITE MAP |
|
| FEATURED PRODUCTS |
|
| |
| |
Drilling Today Market Place for - Water Well Drilling Rigs, Dth Drilling Rigs, Rotary Drilling Rigs, Dth Hammers, Button Bits, Upvc Casing Pipes, Mud Pump, Drill Rods, Hydraulic Pumps, Rock Well Hoses, Down the Hole Drilling rigs, Hydraulic Drilling Rigs, Combination Drilling Rigs, Mud Rotary Drilling Rigs, Direct Rotary Drilling Rigs, Blast Hole Drilling Rigs, Down the Hole Hammers Drill Bits Dth Hammers , Carbide Button Bits, Drag Bits, Pdc Drilling Bits, Diamond Bits |
| |
|
Drilling Today Here |
Mailing Address:
Drilling Today
House A-145, Shivpuri, Airport Road, Opp. Subodh Girls College, Sanganer, Jaipur 302011
Rajasthan INDIA
Phone: +91 141 2793166
Cell: +91 9414 219 166 |
|
|
| |
 |
| Home | Products | Contact Us |
|
|
| Drilling Rigs |
Tractor Mounted Drilling Rigs - KLR TBW 40, DTH Drill Rig
Technical Specifications
Description
KLR TBW 40, DTH is a Tractor Mounted Top drive all hydraulically
operated Drilling Rig extracting main power from Tractor Engine, is
capable of drilling using DTH method to a Depth of 150 Mt.
Drilling Capacity
| DTH Drilling |
Units |
|
Metric |
FPS |
| Bore Diameter |
114 mm |
4.5 Inch |
| Max Drilling Depth |
150 mtrs |
500 feet |
| Max. Overburden Drilling Diameter |
152 mm |
6 inch |
| Max. Drilling depth |
45 mtr |
150 feet |
|
Note: Under favorable Drilling conditions.
Mast Structures
Sturdy structural channel type mast of electrically welded
construction, main members made out of heavy duty structural steel
channels reinforced with suitable cross members, so that it will be strong
enough to withstand the varying drilling loads.
| Mast length |
5720 mm |
| Rotary Head Travel |
4572 mm |
| Centraliser Opening |
203.0 mm (8 Inches) |
| Raising and Lowering |
With hydraulic cylinder |
|
Top Head Rotary Drive
Heavy duty hydraulically driven top head rotation unit will be
provided. This unit travels on the mast and is of sturdy
construction to absorb sudden shock loads.
| Max. Speed |
100 rpm |
| Maximum Torque |
235 kg f-m |
| Drive Type |
Orbital Motor |
| No. of motors |
One number |
|
Feed System
Feed system is provided with adequate travel for handling drill
pipes upto 3.0 Mt. Long. The feed and hoist are actuated by a suitable
hydraulic cylinder with wire rope and pulley arrangement. The feed system
has the following capabilities.
| Pull up force |
4500 Kgf |
| Pull down force |
2400 Kgf |
| Pull up speed |
40 m/min |
| Pull down speed |
65 m/min |
| Reeving ratio(wire rope) |
1:3 |
|
The feed system will be incorporated with Hold back arrangement to
control and limit weight on bit, rapid and slow feed arrangement to
suit the variable ground conditions.
Hydraulic System
| Max. Operating pressure |
160 kg/cm2 |
| Hydraulic Tank capacity |
300 Lts. |
| Filtration (Nom.) Return line |
10 microns |
| Hydraulic Oil Cooler |
40 GPM (Fin type Oil to Air) |
|
Prime Mover
Power required for the rig hydraulics shall be drawn from the tractor
engine through the out put shaft (PTO).
Stabilizers (Jacks)
System consists of three hydraulic leveling jacks with Reverse flow
restricted valves to ensure safe operation. Two numbers are at the front
(Operator) of the rig controlled by two separate valves and one jack in
the rear side of the rig controlled by a single valve.
| Type |
hydraulic cylinder |
| No. of Jacks |
3 Nos. |
|
Breakout Wrench
The Drill Rig is equipped with Hydraulically operated breakout
wrench for breaking drill pipes.
| Cylinder bore diameter |
80 mm |
3.1 Inch |
| Stroke |
300 mm |
12 Inch |
|
Water Injection Pump
The drill rig will be provided with Hydraulically operated triplex
plunger pump, for injecting water/foam with necessary piping and flow
control valve.
| Max. Flow |
36 lpm |
| Max. Pressure |
40 kg/cm2 |
|
Air Compressor
Air compressor of suitable capacity as mentioned can be used for
carrying out the DTH drilling activity.
| Air compressor |
650 cfm / 200 psi |
| Make |
Reputed make |
|
Note: The compressor shall be mounted on separate two wheel single
dummy axle with mechanical stabilizers, suitable toeing arrangement.
Air Line Lubricator
Air Line Lubricator of capacity mentioned below shall be mounted
for the supply of lubricating Oil to the hammer.
| Capacity |
900 cfm / 200 psi |
| Make |
Reputed make |
|
KLR Drilling Rigs
can be supplied in custom-built models in various
Configurations as indicated below, Mounting features to suit
all special requirements and Technical specifications can be
offered accordingly.
|
| KLR TBW 40 DTHR
capable of drilling up to 150 Meters both in DTH and Rotary
drilling, core drilling (Combination Rig) |
|
|
|
|
| |
|
|
|
|
| |
| Terms and Conditions - Disclaimer Copyright © 2009 dthrotarydrilling.com All rights reserved. |
| |
|
|
|
|
