Drilling Today

Manufacturers Exporters and Suppliers of Thunder Hammer, Dth Drilling Rigs, Tractor Mounted Dth Drilling Rigs, Trolley Mounted Dth Drilling Rigs, Skid Mounted Dth Drilling Rigs, Dth Rotary Drilling Rigs, Trailer Mounted Dth Drilling Rigs, Mini Dth Drilling Rigs, Hydraulic Dth Drilling Rigs, Hand Pump Dth Drilling Rigs, Water Well Dth Drilling Rigs, Dth Combination Drilling Rigs.

Dth Rotary Drilling Rigs for sale Trailer Mounted Dth Drilling Rigs for saleMini Dth Drilling Rigs for saleHydraulic Dth Drilling Rigs for sale
Hand Pump Dth Drilling Rigs for sale
Water Well Dth Drilling Rigs for sale
Dth Combination Drilling Rigs for sale

Dth Drilling Rigs
Rotary Drilling Rigs
Combination Drilling Rigs
Dth Cum Rotary Drilling Rigs
Blast Hole Drilling Rigs
Core Drilling Rigs
Wagon Drills
Tractor Mounted Drilling Rigs
Reverce Circulation drilling Rigs
Inwell Drilling Rigs
Trailer Mounted Drill Rig
Self Propelled Skid Mounted Rig
Diamond Core Drilling Rig
Mini Truck Mounted Drilling Rig
Hydro Facturing Equipments
Auto Loader DTH Drilling Rig
Hand Pump Drilling Rigs
Trolley Mounted Drill Rigs
Portable Drilling Rigs
Crawler Mounted Down the Hole
Water Well Drilling Rig
Hydraulic Down the Hole, Drilling Rig
Horizontal Drilling Rigs
Dual Rotary Drilling Rigs
Hydra Drills
Auger Drills
Soil Investigation Drilling Rigs
Foundation Drilling Rigs
Geothermal Drilling Rigs


Drilling Today Market Place for - Water Well Drilling Rigs, Dth Drilling Rigs, Rotary Drilling Rigs, Dth Hammers, Button Bits, Upvc Casing Pipes, Mud Pump, Drill Rods, Hydraulic Pumps, Rock Well Hoses, Down the Hole Drilling rigs, Hydraulic Drilling Rigs, Combination Drilling Rigs, Mud Rotary Drilling Rigs, Direct Rotary Drilling Rigs, Blast Hole Drilling Rigs, Down the Hole Hammers Drill Bits Dth Hammers , Carbide Button Bits, Drag Bits, Pdc Drilling Bits, Diamond Bits


Drilling Today Here
Mailing Address:
Drilling Today
House A-145, Shivpuri, Airport Road, Opp. Subodh Girls College, Sanganer, Jaipur 302011 Rajasthan INDIA
Phone: +91 141 2793166
Cell: +91 9414 219 166

Manufacturers and Exporters of Dth Drilling Rigs
DTH Rigs
Diamond Core Drilling Rigs
RC Rigs
MTM Rigs
Hydro Fractering Unit
Blast Hole Drilling
Tractor Mounted Rigs
Refurbished Rigs
Pumping Test Unit
Wagon Drill
Thunder Hammer
Thunder Hammer
Hammer Name Thunder Hammer HT Hammer
Part Number H60T H65HT
Outside Dia (mm) 138.00 148.00
Recomm. Bit size (mm) 152.40 to 216.00 165.10 to 228.60
To Sub Thread (IN) 2-7/8" Reg Pin 2-7/8" Reg Pin
Ham. Wt. without Bit (Kg.) 97.00 103.00
Total Len. without Bit (mm) 1285.00 1285.00
Wrench Flat (mm) 90.00 90.00
Working Pressure (Bar) 7.5-21 7.5-21
Component Name H60T H65HT
Piston Case / Barrel HB60T HB65HT
Piston HP60T HP65HT
Control Tube HCT60T HCT65HT
Top Sub / Back Head HC60T HC65HT
Driver Sub / Front Chuck HFC60T HFC65HT
Air Distributor HAD60T HAD65HT
Guide Sleeve / Assembly Bush HAB60T HAB65HT
Bit Retainer Ring / Bit Lock HBL60T HBL65HT
Dart / Check Valve HCKV60T HCKV65HT
Rubber Check Valve Cap HCKVC60T HCKVC65HT
Spring HS60T HS65HT
Rubber Washer HRW60T HRW65HT
O Ring / Bit Lock O Ring HOR60T HOR65HT
Choke HBC614 HBC65HT
Front Chuck Rubber Cap HFCRC60T HFCRC65HT
Back Head Rubber Cap HCRC60T HCRC65HT

•   For use in hard rock application
•   Valve less DTH Hammer design
•   Reversible Cylinder (wear sleeve)
•   Excellent under water characteristics
•   Less wear & tear
•   Easy to maintain
•   Long life

Before shutting down at the end of each shift, we recommend the following procedures:
  1. Flush Hammer with air/water for a few minutes, then turn off water injection
  2. Flush Hammer with air/oil for a few minutes.  This will coat the internal Hammer parts preventing corrosion/rust.
  3. Never leave the tool in a wet / muddy hole.  Pull back from bottom as far as necessary to prevent the Hammer sitting under water.
  4. It is also good practice to pour at least half a litre of oil down the drill at start up of a new shift.
  5. If the Hammer is removed from the drill rig for any reason, it is wise to pour a quantity of oil into it and block both ends, providing the flushing as outlined in steps one and two above have been carried out.  If steps one and two have not been carried out the Hammer should be stripped, cleaned and oiled before being stored.
Terms and Conditions - Disclaimer Copyright © 2009 dthrotarydrilling.com All rights reserved.